Announcement

Collapse
No announcement yet.

Upload issue

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • mavrik
    replied
    In socle the issue with this post:
    Problem uploading to Arduino Micro (hangs on Uploading...)
    post#2
    https://forum.arduino.cc/index.php?topic=224416.0

    Thanks for your help

    Leave a comment:


  • kayven@4d
    replied
    Hi,

    I'm assumed that you followed the setup procedure for installing 4duino in the Arduino Environment.


    You can also use the arduino IDE
    to upload the empty project after you compile it using the WS4, just look for the .ino file on the working dir.

    If above does not work, please have a look on the threads shown below:

    Problem uploading to Arduino Micro (hangs on Uploading...)
    post#2
    https://forum.arduino.cc/index.php?topic=224416.0

    Or

    Re-loading the bootloader
    https://electronut.in/bootloader-atmega32u4/

    Best regards,
    Kayven

    Leave a comment:


  • mavrik
    commented on 's reply
    How I can do that ?

  • Johannes
    commented on 's reply
    Did you try disconnecting the LCD TX line while uploading to the Arduino?

  • mavrik
    replied
    Hi,

    I use Workshop 4 V4.5.0.17. I think it's the latest version.

    I have try to send an empty project and I have the same error.

    Thanks for your help.

    Leave a comment:


  • kayven@4d
    replied
    Hi,

    Thank you for the information.



    At the moment, I was trying to replicate the problem.


    What about the WS4 version you are using? Is it in the latest version?

    Did you try to upload a sample code/ empty project ? if not, just open Workshop >> File >> New >> 4Duino >> Next >> Basic Graphics >> Save >> Com'n Load.

    This will help us to come up to a conclusion.

    Please, let me know if it works.


    Best regards,
    Kayven
    Last edited by [email protected]; 2nd March 2019, 05:17 PM.

    Leave a comment:


  • mavrik
    replied
    Hi,

    I have try a new usb cable and it's the same.
    I also try a new computer and I have the same error.

    Leave a comment:


  • mavrik
    replied
    Hin

    The Arduino IDE version is 1.8.8.

    I have 2 CAN-BUS Shield V2.0 board plug on my 4duino. I have try to download the program without the 2 board but it's the same.

    Leave a comment:


  • kayven@4d
    replied
    Hi,


    It appears that the board(ATmel chip) is not corresponding.


    What is the version of your Arduino IDE?.
    Is there a device connected to * Rx and * Tx Pins? If so, it is recommended to disconnect the device connected to it, these pins are used during the upload.

    Best regards,
    Kayven

    Leave a comment:


  • mavrik
    replied
    Hi,

    I have try to disconnect/ reconnect the display and it's the same.
    I have try to change the port comm (6 to 11).

    Leave a comment:


  • kayven@4d
    replied
    Hi,

    Thanks for posting here.

    In some cases, this also happens when the device is not properly connected or the comm port is being used.


    Did you try disconnecting the display module then re-uploading the code?

    If so, please give us more information that you have made?

    Best regards,
    Kayven

    Leave a comment:


  • mavrik
    started a topic Upload issue

    Upload issue

    Hello,

    I have an upload issue. Click image for larger version

Name:	Capture d’écran 2019-02-25 à 10.03.51.png
Views:	41
Size:	51.6 KB
ID:	67219
Working...
X